Car TalkCar MaintenanceCar ACHow To Flush A Car AC System After Compressor Failure?

How To Flush A Car AC System After Compressor Failure?

If your car’s AC compressor just failed, you have a big job ahead. But here’s the most important step: you must flush the system. When a compressor breaks, it sends tiny pieces of metal and debris throughout the entire AC system. If you skip this step, those tiny pieces will instantly destroy your brand-new compressor. We show you the detailed, safe way how to flush a car AC system after a compressor failure:

Why Do You Need to Flush the Air Conditioning Unit?

A compressor failure in your car’s AC system means you have to install a new one. But flushing the system is requisite before the installation.

Solid substances can form in the refrigerant circuit over time, causing damage to several components. Also, a compressor can send tiny metal fragments into the system at the time of failure.

These fragments are likely to block the system’s small passages, which will remain even after changing the compressor. These metal shards can also harm the new compressor.

For these reasons, you should always flush the AC unit to remove the metal particles and other solids whenever changing the failed compressor.

how do you flush a car ac system
How do you flush a car ac system (Photo: istockphoto)

How to Flush AC System after Compressor Failure?

You have to flush the condenser of the AC system before replacing the compressor. However, most automakers, including Toyota, recommend the replacement of the condenser and hoses instead of flushing in case of contamination.

Two auto manufacturers that recommend condenser flushing are GM and Ford. GM suggests the use of only R-134a for the process. They also want you to do it in a recharging machine to reduce refrigerant loss. On the other hand, Ford approves of using VSL338 terpene-based solvent for the flushing.

Here are several methods of how to flush AC system after compressor failure. Remember that you have to flush nothing but the condenser, hoses, and evaporator.

Before system flushing, it’s necessary to check the refrigerant with the help of a gas analyzer. The refrigerant is pumped out with the help of a filling station.

Use AC flushing equipment.

how to flush ac system at home
How to flush ac system at home (Photo: istockphoto)

There are plenty of flush kits for performing an open-loop flushing process. The flusher includes a tank, catch pan, hose, and adapters. Using such a kit is one of the easiest ways to flush the AC system, and the whole process takes just about 15 minutes. Use a solvent that does not corrode or harm the inner components. After the cleaning is done, leave those components in the open air to dry properly.

If you want a deep cleaning and to reduce the flushing time, purchase a power flushing kit. It dislodges the hardened particles and completes the cleaning quickly. However, such a machine is expensive, costing around $2,000 to $3,000.

Use flushing liquid.

Instead of using a cleaning solvent, you can also use a flushing liquid (like a chemical- or water-based fluid). This process works better for R1234yf air-conditioning systems and for the systems being converted to R134a from R12.

You must use nitrogen to dry the components after finishing the cleaning. Blow out each part and pipe one by one with nitrogen. These are the ways how to flush AC system after compressor failure. Flushing is done to remove not only solid buildups from the AC unit but also dirty liquid and lubricating oil residue.

Watch more:

After flushing, the system must be refilled with the right amount of freon. Connect high and low-pressure lines and evacuate the system. Then, pump the right amount of freon by setting parameters at the filling station.  

Conclusion: Don’t Skip the Clean Sweep

Repairing a failed AC compressor is a big job, but remember that the flush is the most critical step. When the old compressor died, it filled your system with tiny bits of metal and sludge. If you install a brand-new compressor without thoroughly cleaning the lines, that old contamination will travel instantly and destroy the new part.

Take the time to use the proper flushing procedures. It’s the only way to guarantee a perfectly clean system, ensuring your new compressor lasts for years and keeps your car cool!

Tsukasa Azuma
Tsukasa Azuma
Tsukasa Azuma is the resident car expert at Car From Japan. He owns a car repair shop in downtown Osaka, and his years of hands-on experience shine through in his informative blog posts. Tsukasa provides top-notch car maintenance tips and keeps readers up-to-date on the latest trends in the auto industry, offering a unique and insightful perspective on everything car-related. His blog has become a go-to resource for anyone wanting to keep their car in top shape.
RELATED ARTICLES

LEAVE A REPLY

Please enter your comment!
Please enter your name here

referral program

Most Popular