How To Program Dodge Key Fob Without a Working One?

If you want to replace the key fob of a new Dodge car, knowing the key fob programming becomes essential.

But when there is no working key available, the situation becomes complex. The only thing you can do is learn how to program dodge key fob without a working one and perform the steps accordingly.

How to Program a Dodge Key Fob

The procedure to program a Dodge key fob involves some simple steps that you can perform as per the following guideline.

Step 1: Enter into the Dodge car of any model and sit on the driver’s seat. Within the range of 10 seconds, press and release the “LOCK BUTTON” of the key fob five times. In this step, timing is crucial.

Step 2: Now, press the “UNLOCK BUTTON.” While holding it, insert the key into the car ignition and turn it in the ignition to “RUN” mode. Do not take your finger off of the “UNLOCK BUTTON.”

Step 3: While pressing down the “UNLOCK BUTTON,” do the same on the “PANIC BUTTON” for one full second. Then, release both buttons together.

Step 4: Now, hold down the “UNLOCK” and “LOCK” buttons together before releasing them simultaneously.

Step 5: Once again, press the “UNLOCK BUTTON.”

Step 6: Now, the Dodge car should recognize the key fob.

How to Program Dodge Key Fob Without a Working One

If the key fob is not working, it becomes more difficult to program it. However, there is also a solution to this issue called Manual Programming Procedure that does not need a scan tool.

Step 1: Connect pin 1 or pin 4 of the 16-way data link connector to chassis ground.

Step 2: Shut all the vehicle doors and turn off the ignition key.

Step 3: Turn the ignition key to the Accessory position.

Step 4: Now is the time to turn off the ignition. As a result, door locks will cycle for one time in programming mode.

Step 5: For every key FOB, press any button three times in a row to execute the code programming.

Step 6: After the completion of the programming, the door locks cycle will take place once again.

SEE MORE: Want to Install a Keyless Entry System? Here’s How

What To Do If the Battery of the Key Fob Is Dead?

Sometimes, the key fob battery is dead or has too low charge to function. In that situation, try this trick to open the Dodge vehicle doors.

The good news is, there may be a hidden key inside the fob. To locate it, flip the fob to get to its opposite side and slide the switch of the top left corner to pull out the silver key. Now, this key can easily unlock the car doors.

Place back the key inside the key fob for its security purpose.Push the start button with the Dodge key fob and press the brake with your feet.

Common Issues of The Dodge Key Fob and Solutions

We hope that with the above notices, you have grasped how to program Dodge key fob without a working one quickly and effectively.

Not only do you need to understand how the key fob works and assemble and reprogram it effectively, but you also need to know more about some of its problems. Below are some common issues with Dodge key fobs and how to identify and solve them.

Key not responding

If your key is not responding, the main cause is usually a dead battery. The battery will power the wireless signal and the battery will naturally drain over time.

Before assuming that the key is having a worse and more complicated problem, you can try replacing the battery first.

Double-check and make sure you choose the right type of battery for your key to avoid crashing or damaging it.

After replacing the battery and reprogramming the car key, you can pay attention and see if there are signs such as slow locking, programming interruptions, or power problems.

Your vehicle does not recognize the Dodge key fob

If your key seems to work without any problems (for example, the light flashes when pressing the button), but the car does not respond, you may need to review the programming operations to see if they are correct.

Before reprogramming again, refer to the exact programming rules in the owner’s manual. Remember that different car manufacturers and models will have their own programming rules.

So programming in the wrong order can lead to the problem of the car not recognizing the Dodge key fob. In addition, pay attention to the time requirements and specific operations needed during certain periods.

The Key fob not working after programming

If you have replaced the battery and carefully followed the programming instructions in your manual, but your key still does not respond, do not hesitate to seek professional help to save time and effort.

In these cases, the problem is not just with the key fob or the programming sequence but is likely related to more complex issues.

These may involve damage, corrosion, or malfunction within the key, a faulty transponder, or a problem with the vehicle’s anti-theft system.

A qualified locksmith or dealer service center, such as Encore Chrysler Dodge Jeep Ram, has the specialized tools and expertise to diagnose and resolve these more complex issues.

They can determine the root cause of the problem and provide the necessary repair or replacement services to get your key working again.

FAQs on Programming Dodge Key Fob

Check out this video from Tomahawk DIY for more safety precautions and notices when programming a Dodge key fob!

Conclusion

If you are curious to know how to program Dodge key fob without a working one, follow these steps above.

Thus, it should be an easy process to program a Dodge key fob. But it is also possible for the newbies to face a problem. In that case, take suggestions from the expert Dodge vehicle specialists!

For more insightful Car maintenance tips, follow Car From Japan today!