How To Program Dodge Key Fob Without a Working One?

If you want to replace the key fob of a new Dodge car, knowing the key fob programming becomes essential. But when there is no working key available, the situation becomes complex. The only thing you can do is learn how to program dodge key fob without a working one and perform the steps accordingly.

How to Program a Dodge Key Fob

The procedure to program a Dodge key fob involves some simple steps that you can perform as per the following guideline.

1. Enter into the Dodge car of any model and sit on the driver’s seat. Within the range of 10 seconds, press and release the “LOCK BUTTON” of the key fob five times. In this step, timing is crucial.
2. Now, press the “UNLOCK BUTTON.” While holding it, insert the key into the car ignition and turn it in the ignition to “RUN” mode. Do not take your finger off of the “UNLOCK BUTTON.”
3. While pressing down the “UNLOCK BUTTON,” do the same on the “PANIC BUTTON” for one full second. Then, release both buttons together.
4. Now, hold down the “UNLOCK” and “LOCK” buttons together before releasing them simultaneously.
5. Once again, press the “UNLOCK BUTTON.”
6. Now, the Dodge car should recognize the key fob.

How to Program Dodge Key Fob Without a Working One

If the key fob is not working, it becomes more difficult to program it. However, there is also a solution to this issue called Manual Programming Procedure that does not need a scan tool.

Step 1: Connect pin 1 or pin 4 of the 16-way data link connector to chassis ground.

Step 2: Shut all the vehicle doors and turn off the ignition key.

Step 3: Turn the ignition key to the Accessory position.

Step 4: Now is the time to turn off the ignition. As a result, door locks will cycle for one time in programming mode.

Step 5: For every key FOB, press any button three times in a row to execute the code programming.

Step 6: After the completion of the programming, the door locks cycle will take place once again.

SEE MORE

• Want to Install a Keyless Entry System? Here’s How
• Effective Ways to Prevent Keyless Car Theft

What If the Battery of the Key Fob Is Dead

Sometimes, the key fob battery is dead or has too low charge to function. In that situation, try this trick to open the Dodge vehicle doors:

The good news is, there may be a hidden key inside the fob. To locate it, flip the fob to get to its opposite side and slide the switch of the top left corner to pull out the silver key. Now, this key can easily unlock the car doors.

Place back the key inside the key fob for its security purpose.Push the start button with the Dodge key fob and press the brake with your feet.

FAQs on Program Dodge Key Fob

1. Can I program a Dodge key fob without a working one myself?

You can program a Dodge key fob without a working one by following specific steps outlined in your vehicle’s owner’s manual or seeking guidance from Dodge customer support. 

The process typically involves a series of actions, including entering the vehicle and using the ignition switch.

2. What information do I need to program a Dodge key fob without a working one?

To program a new Dodge key fob, you’ll typically need the vehicle identification number (VIN) and the new key fob itself. Some vehicles may also require a PIN code, which can be obtained from a Dodge dealership or customer support.

3. Are there different procedures for programming Dodge key fobs for different models or years?

The programming procedure may vary depending on the Dodge model and model year. It’s essential to consult your vehicle’s owner’s manual or seek specific instructions related to your particular Dodge model.

4. Can I program multiple Dodge key fobs using this method?

You can usually program multiple Dodge key fobs using the programming method outlined in your owner’s manual. The process typically allows you to program several key fobs to work with your vehicle.

5. Are there any safety precautions I should take when programming a Dodge key fob?

While programming a key fob is generally a straightforward process, it’s essential to follow safety precautions and the provided instructions carefully.

Check out this video from Tomahawk DIY for more safety precautions and notices when programming a Dodge key fob!

Ensure that you are in a secure location and have all necessary information and components before beginning the programming process.

6. What should I do if I encounter difficulties or have questions during the programming process?

If you encounter challenges or have questions while programming a Dodge key fob, it’s advisable to consult your vehicle’s owner’s manual for troubleshooting tips or contact Dodge customer support or a dealership for assistance.

They can provide guidance and support to ensure a successful programming process.

7. Can a locksmith or auto technician help you learn how to program dodge key fob without a working one?

Professional locksmiths or auto technicians with experience in Dodge vehicles can assist in programming a new key fob if you are unsure about the process or encounter difficulties.

8. Is it possible to program a Dodge key fob without a working one for all Dodge models?

The ability to program a Dodge key fob without a working one may vary by model and model year.

While most modern Dodge vehicles support this process, it’s essential to consult your specific vehicle’s documentation or contact Dodge customer support for accurate information regarding your model.

Conclusion

If you are curious to know how to program dodge key fob without a working one, follow these steps. Thus, it should be an easy process to program a Dodge key fob. But it is also possible for the newbies to face a problem. In that case, take suggestions from the expert Dodge vehicle specialists.